UPLOAD ... done Ctrl+C to exit ... # UPLOAD ... done Ctrl+C to exit ... NOTICE: CPU: STM32MP157C?? Rev.Z NOTICE: Model: Octavo OSD32MP1 BRK board NOTICE: dbg-31 INFO: Reset reason (0x15): INFO: Power-on Reset (rst_por) INFO: PMIC version = 0x21 INFO: FCONF: Reading TB_FW firmware configuration file from: 0x2ffe3000 INFO: FCONF: Reading firmware configuration information for: stm32mp_io INFO: Using EMMC INFO: Instance 2 INFO: Boot used partition fsbl1 NOTICE: dbg-44: END NOTICE: BL2: v2.4-r1.0(debug):v2.4-stm32mp-r1-dirty NOTICE: BL2: Built : 16:59:14, Feb 9 2023 INFO: BL2: Doing platform setup INFO: RAM: DDR3-DDR3L 16bits 533000Khz WARNING: Couldn't find property st,phy-cal in dtb INFO: Memory size = 0x20000000 (512 MB) INFO: BL2: Loading image id 31 INFO: Loading image id=31 at address 0x2ffff000 INFO: Image id=31 loaded: 0x2ffff000 - 0x2ffff226 INFO: FCONF: Reading FW_CONFIG firmware configuration file from: 0x2ffff000 INFO: FCONF: Reading firmware configuration information for: dyn_cfg INFO: FCONF: Reading firmware configuration information for: stm32mp1_firewall INFO: BL2: Loading image id 4 INFO: Loading image id=4 at address 0x2ffc5000 INFO: Image id=4 loaded: 0x2ffc5000 - 0x2ffd847c WARNING: Not a known TEE, use default loading options. INFO: BL2: Skip loading image id 21 INFO: BL2: Skip loading image id 22 INFO: BL2: Loading image id 23 INFO: Loading image id=23 at address 0xc0500000 INFO: Image id=23 loaded: 0xc0500000 - 0xc0513c7e INFO: BL2: Loading image id 26 INFO: Loading image id=26 at address 0x2ffc0000 INFO: Image id=26 loaded: 0x2ffc0000 - 0x2ffc40c8 INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0xc0100000 INFO: Image id=5 loaded: 0xc0100000 - 0xc01cfa18 NOTICE: BL2: Booting BL32 INFO: Entry point address = 0x2ffc5000 INFO: SPSR = 0x1d3 NOTICE: SP_MIN: v2.4-r1.0(debug):v2.4-stm32mp-r1-dirty NOTICE: SP_MIN: Built : 16:58:55, Feb 9 2023 INFO: ARM GICv2 driver initialized INFO: Set calibration timer to 60 sec INFO: stm32mp1 IWDG1 is secure INFO: SP_MIN: Initializing runtime services INFO: SP_MIN: Preparing exit to normal world U-Boot 2020.10-stm32mp-r1 (Feb 26 2023 - 11:09:22 +0200) CPU: STM32MP157C?? Rev.Z Model: Octavo OSD32MP1 BRK board Board: stm32mp1 in trusted - stm32image mode (st,stm32mp157c-osd32mp1-brk) DRAM: 512 MiB Clocks: - MPU : 650 MHz - MCU : 208.878 MHz - AXI : 266.500 MHz - PER : 64 MHz - DDR : 533 MHz STM32Programmer key pressed, entering download mode... WDT: Started with servicing (32s timeout) NAND: 0 MiB MMC: STM32 SD/MMC: 0, STM32 SD/MMC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial invalid MAC address in OTP 00:00:00:00:00:00 Net: No ethernet found. Hit any key to stop autoboot: 0 Boot over mmc1! Saving Environment to MMC... Writing to redundant MMC(1)... OK switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:4... Found U-Boot script /boot.scr.uimg 3639 bytes read in 28 ms (126 KiB/s) ## Executing script at c4100000 Executing SCRIPT on target=mmc1 Saving Environment to MMC... Writing to MMC(1)... OK switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:4... Found /mmc1_extlinux/extlinux.conf Retrieving file: /mmc1_extlinux/extlinux.conf 359 bytes read in 28 ms (11.7 KiB/s) Retrieving file: /splash.bmp 170122 bytes read in 36 ms (4.5 MiB/s) 1:    osd32mp1-brk-sdcard Retrieving file: /uImage 7704856 bytes read in 203 ms (36.2 MiB/s) append: root=/dev/mmcblk1p6 rootwait rw console=ttySTM0,115200 init=/sbin/init firmware_class.path=/lib/firmware/ Retrieving file: /stm32mp157c-osd32mp1-brk.dtb 60304 bytes read in 33 ms (1.7 MiB/s) ## Booting kernel from Legacy Image at c2000000 ... Image Name: Linux kernel Created: 2024-04-07 19:49:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 7704792 Bytes = 7.3 MiB Load Address: c2000040 Entry Point: c2000040 Verifying Checksum ... OK ## Flattened Device Tree blob at c4000000 Booting using the fdt blob at 0xc4000000 XIP Kernel Image Loading Device Tree to cffee000, end cffffb8f ... OK Starting kernel ... INFO: CPU 0 IT Watchdog 2 INFO: CPU : 0 INFO: sp_usr : 0x0 INFO: lr_usr : 0x0 INFO: spsr_irq : 0x60000193 INFO: sp_irq : 0xc133a200 INFO: lr_irq : 0xc0100b20 INFO: spsr_fiq : 0x0 INFO: sp_fiq : 0xc133a224 INFO: lr_fiq : 0xc133a224 INFO: spsr_svc : 0x60000013 INFO: sp_svc : 0xc1201f50 INFO: lr_svc : 0xc0108e3c INFO: spsr_abt : 0x0 INFO: sp_abt : 0xc133a20c INFO: lr_abt : 0xc133a20c INFO: spsr_und : 0x0 INFO: sp_und : 0xc133a218 INFO: lr_und : 0xc133a218 INFO: spsr_mon : 0x60000093 INFO: sp_mon : 0x2ffd8a80 INFO: lr_mon : 0xc0117948 INFO: scr : 0x225 INFO: pmcr : 0x41072000