UPLOAD ... done
Ctrl+C to exit ...
#
UPLOAD ... done
Ctrl+C to exit ...
NOTICE:  CPU: STM32MP157C?? Rev.Z
NOTICE:  Model: Octavo OSD32MP1 BRK board
NOTICE:  dbg-31
INFO:    Reset reason (0x15):
INFO:      Power-on Reset (rst_por)
INFO:    PMIC version = 0x21
INFO:    FCONF: Reading TB_FW firmware configuration file from: 0x2ffe3000
INFO:    FCONF: Reading firmware configuration information for: stm32mp_io
INFO:    Using EMMC
INFO:      Instance 2
INFO:    Boot used partition fsbl1
NOTICE:  dbg-44: END
NOTICE:  BL2: v2.4-r1.0(debug):v2.4-stm32mp-r1-dirty
NOTICE:  BL2: Built : 16:59:14, Feb  9 2023
INFO:    BL2: Doing platform setup
INFO:    RAM: DDR3-DDR3L 16bits 533000Khz
WARNING: Couldn't find property st,phy-cal in dtb
INFO:    Memory size = 0x20000000 (512 MB)
INFO:    BL2: Loading image id 31
INFO:    Loading image id=31 at address 0x2ffff000
INFO:    Image id=31 loaded: 0x2ffff000 - 0x2ffff226
INFO:    FCONF: Reading FW_CONFIG firmware configuration file from: 0x2ffff000
INFO:    FCONF: Reading firmware configuration information for: dyn_cfg
INFO:    FCONF: Reading firmware configuration information for: stm32mp1_firewall
INFO:    BL2: Loading image id 4
INFO:    Loading image id=4 at address 0x2ffc5000
INFO:    Image id=4 loaded: 0x2ffc5000 - 0x2ffd847c
WARNING: Not a known TEE, use default loading options.
INFO:    BL2: Skip loading image id 21
INFO:    BL2: Skip loading image id 22
INFO:    BL2: Loading image id 23
INFO:    Loading image id=23 at address 0xc0500000
INFO:    Image id=23 loaded: 0xc0500000 - 0xc0513c7e
INFO:    BL2: Loading image id 26
INFO:    Loading image id=26 at address 0x2ffc0000
INFO:    Image id=26 loaded: 0x2ffc0000 - 0x2ffc40c8
INFO:    BL2: Loading image id 5
INFO:    Loading image id=5 at address 0xc0100000
INFO:    Image id=5 loaded: 0xc0100000 - 0xc01cfa18
NOTICE:  BL2: Booting BL32
INFO:    Entry point address = 0x2ffc5000
INFO:    SPSR = 0x1d3
NOTICE:  SP_MIN: v2.4-r1.0(debug):v2.4-stm32mp-r1-dirty
NOTICE:  SP_MIN: Built : 16:58:55, Feb  9 2023
INFO:    ARM GICv2 driver initialized
INFO:    Set calibration timer to 60 sec
INFO:    stm32mp1 IWDG1 is secure
INFO:    SP_MIN: Initializing runtime services
INFO:    SP_MIN: Preparing exit to normal world


U-Boot 2020.10-stm32mp-r1 (Feb 26 2023 - 11:09:22 +0200)

CPU: STM32MP157C?? Rev.Z
Model: Octavo OSD32MP1 BRK board
Board: stm32mp1 in trusted - stm32image mode (st,stm32mp157c-osd32mp1-brk)
DRAM:  512 MiB
Clocks:
- MPU : 650 MHz
- MCU : 208.878 MHz
- AXI : 266.500 MHz
- PER : 64 MHz
- DDR : 533 MHz
STM32Programmer key pressed, entering download mode...
WDT:   Started with servicing (32s timeout)
NAND:  0 MiB
MMC:   STM32 SD/MMC: 0, STM32 SD/MMC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
invalid MAC address in OTP 00:00:00:00:00:00
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
Boot over mmc1!
Saving Environment to MMC... Writing to redundant MMC(1)... OK
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:4...
Found U-Boot script /boot.scr.uimg
3639 bytes read in 28 ms (126 KiB/s)
## Executing script at c4100000
Executing SCRIPT on target=mmc1
Saving Environment to MMC... Writing to MMC(1)... OK
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:4...
Found /mmc1_extlinux/extlinux.conf
Retrieving file: /mmc1_extlinux/extlinux.conf
359 bytes read in 28 ms (11.7 KiB/s)
Retrieving file: /splash.bmp
170122 bytes read in 36 ms (4.5 MiB/s)
1:    osd32mp1-brk-sdcard
Retrieving file: /uImage
7704856 bytes read in 203 ms (36.2 MiB/s)
append: root=/dev/mmcblk1p6 rootwait rw console=ttySTM0,115200 init=/sbin/init firmware_class.path=/lib/firmware/
Retrieving file: /stm32mp157c-osd32mp1-brk.dtb
60304 bytes read in 33 ms (1.7 MiB/s)
## Booting kernel from Legacy Image at c2000000 ...
   Image Name:   Linux kernel
   Created:      2024-04-07  19:49:19 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7704792 Bytes = 7.3 MiB
   Load Address: c2000040
   Entry Point:  c2000040
   Verifying Checksum ... OK
## Flattened Device Tree blob at c4000000
   Booting using the fdt blob at 0xc4000000
   XIP Kernel Image
   Loading Device Tree to cffee000, end cffffb8f ... OK

Starting kernel ...

INFO:    CPU 0 IT Watchdog 2
INFO:    CPU : 0
INFO:    sp_usr   : 0x0
INFO:    lr_usr   : 0x0
INFO:    spsr_irq : 0x60000193
INFO:    sp_irq   : 0xc133a200
INFO:    lr_irq   : 0xc0100b20
INFO:    spsr_fiq : 0x0
INFO:    sp_fiq   : 0xc133a224
INFO:    lr_fiq   : 0xc133a224
INFO:    spsr_svc : 0x60000013
INFO:    sp_svc   : 0xc1201f50
INFO:    lr_svc   : 0xc0108e3c
INFO:    spsr_abt : 0x0
INFO:    sp_abt   : 0xc133a20c
INFO:    lr_abt   : 0xc133a20c
INFO:    spsr_und : 0x0
INFO:    sp_und   : 0xc133a218
INFO:    lr_und   : 0xc133a218
INFO:    spsr_mon : 0x60000093
INFO:    sp_mon : 0x2ffd8a80
INFO:    lr_mon : 0xc0117948
INFO:    scr : 0x225
INFO:    pmcr : 0x41072000