NOTICE: CPU: STM32MP157C?? Rev.Z NOTICE: Model: Octavo OSD32MP1 BRK board INFO: Reset reason (0x15): INFO: Power-on Reset (rst_por) INFO: PMIC version = 0x21 INFO: Using SDMMC INFO: Instance 1 INFO: Boot used partition fsbl1 NOTICE: BL2: v2.2-r2.0(debug): NOTICE: BL2: Built : 03:35:11, Dec 6 2020 INFO: Using crypto library 'stm32_crypto_lib' INFO: BL2: Doing platform setup INFO: RAM: DDR3-DDR3L 16bits 533000Khz INFO: Memory size = 0x20000000 (512 MB) INFO: BL2 runs SP_MIN setup INFO: BL2: Loading image id 4 INFO: Loading image id=4 at address 0x2ffeb000 INFO: Image id=4 loaded: 0x2ffeb000 - 0x2ffff000 INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0xc0100000 INFO: STM32 Image size : 888662 INFO: Image id=5 loaded: 0xc0100000 - 0xc01d8f56 WARNING: Skip signature check (header option) NOTICE: ROTPK is not deployed on platform. Skipping ROTPK verification. NOTICE: BL2: Booting BL32 INFO: Entry point address = 0x2ffeb000 INFO: SPSR = 0x1d3 NOTICE: SP_MIN: v2.2-r2.0(debug): NOTICE: SP_MIN: Built : 03:35:17, Dec 6 2020 INFO: ARM GICv2 driver initialized INFO: Set calibration timer to 60 sec INFO: stm32mp IWDG1 (12): Secure INFO: SP_MIN: Initializing runtime services INFO: SP_MIN: Preparing exit to normal world U-Boot 2020.01-stm32mp-r2 (Dec 11 2020 - 21:28:18 +0900) CPU: STM32MP157C?? Rev.Z Model: Octavo OSD32MP1 BRK board Board: stm32mp1 in trusted mode (st,stm32mp157c-osd32mp1-brk) DRAM: 512 MiB Clocks: - MPU : 650 MHz - MCU : 208.878 MHz - AXI : 266.500 MHz - PER : 24 MHz - DDR : 533 MHz WDT: Started with servicing (32s timeout) NAND: 0 MiB MMC: STM32 SD/MMC: 0 Loading Environment from MMC... OK In: serial Out: serial Err: serial invalid MAC address in OTP 00:00:00:00:00:00 Net: No ethernet found. Hit any key to stop autoboot: 0 Boot over mmc0! switch to partitions #0, OK mmc0 is current device Scanning mmc 0:4... Found /mmc0_extlinux/extlinux.conf Retrieving file: /mmc0_extlinux/extlinux.conf 499 bytes read in 24 ms (19.5 KiB/s) Retrieving file: /splash.bmp 18244 bytes read in 25 ms (711.9 KiB/s) 1: OpenSTLinux 2: OpenSTLinux-OSD32MP1 Enter choice: 2: OpenSTLinux-OSD32MP1 Retrieving file: /uInitrd Skipping OpenSTLinux-OSD32MP1 for failure retrieving initrd 1: OpenSTLinux Retrieving file: /uInitrd 3632201 bytes read in 179 ms (19.4 MiB/s) Retrieving file: /uImage 7341840 bytes read in 336 ms (20.8 MiB/s) append: root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw console=ttySTM0,115200 Retrieving file: /stm32mp157c-osd32mp1-brk.dtb 57716 bytes read in 28 ms (2 MiB/s) ## Booting kernel from Legacy Image at c2000000 ... Image Name: Linux-5.4.56 Created: 2020-08-05 7:59:52 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 7341776 Bytes = 7 MiB Load Address: c2000040 Entry Point: c2000040 Verifying Checksum ... OK ## Flattened Device Tree blob at c4000000 Booting using the fdt blob at 0xc4000000 XIP Kernel Image Loading Ramdisk to cfc89000, end cffffc49 ... OK Loading Device Tree to cfc77000, end cfc88173 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.56 (oe-user@oe-host) (gcc version 9.3.0 (GCC)) #1 SMP PREEMPT Wed Aug 5 07:59:52 0 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Octavo OSD32MP1 BRK board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Reserved memory: created DMA memory pool at 0x10000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node mcuram2@10000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10040000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0vring0@10040000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10041000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0vring1@10041000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x10042000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@10042000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x30000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node mcuram@30000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x38000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node retram@38000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 128 MiB at 0xd2000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s50956 r8192 d22772 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 113536 [ 0.000000] Kernel command line: root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw console=ttySTM00 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 301552K/458752K available (11264K kernel code, 871K rwdata, 3424K rodata, 1024K init, 214K ) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x4f4 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 4407952s [ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000028] Switching to timer-based delay loop, resolution 41ns [ 0.001335] Console: colour dummy device 80x30 [ 0.001384] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=2400) [ 0.001404] pid_max: default: 32768 minimum: 301 [ 0.001660] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001682] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002984] CPU: Testing write buffer coherency: ok [ 0.003534] /cpus/cpu@0 missing clock-frequency property [ 0.003569] /cpus/cpu@1 missing clock-frequency property [ 0.003587] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.059964] Setting up static identity map for 0xc0100000 - 0xc0100060 [ 0.079941] rcu: Hierarchical SRCU implementation. [ 0.104446] smp: Bringing up secondary CPUs ... [ 0.180592] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.180817] smp: Brought up 1 node, 2 CPUs [ 0.180840] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.180850] CPU: All CPU(s) started in SVC mode. [ 0.181721] devtmpfs: initialized [ 0.201618] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.202240] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.202277] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.209284] pinctrl core: initialized pinctrl subsystem [ 0.211662] NET: Registered protocol family 16 [ 0.223294] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.225336] cpuidle: using governor menu [ 0.225797] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.225814] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.226284] Serial: AMBA PL011 UART driver [ 0.229150] stm32-pm-domain pm_domain: domain core-ret-power-domain registered [ 0.229189] stm32-pm-domain pm_domain: subdomain core-power-domain registered [ 0.229206] stm32-pm-domain pm_domain: domains probed [ 0.271040] SCSI subsystem initialized [ 0.271884] usbcore: registered new interface driver usbfs [ 0.271966] usbcore: registered new interface driver hub [ 0.272114] usbcore: registered new device driver usb [ 0.272513] pps_core: LinuxPPS API ver. 1 registered [ 0.272528] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.272560] PTP clock support registered [ 0.272916] EDAC MC: Ver: 3.0.0 [ 0.274283] Advanced Linux Sound Architecture Driver Initialized. [ 0.276089] clocksource: Switched to clocksource arch_sys_counter [ 0.999329] thermal_sys: Registered thermal governor 'step_wise' [ 0.999951] NET: Registered protocol family 2 [ 1.001107] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.001161] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.001230] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.001326] TCP: Hash tables configured (established 4096 bind 4096) [ 1.001480] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.001526] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.001843] NET: Registered protocol family 1 [ 1.002855] RPC: Registered named UNIX socket transport module. [ 1.002876] RPC: Registered udp transport module. [ 1.002887] RPC: Registered tcp transport module. [ 1.002897] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.003265] Trying to unpack rootfs image as initramfs... [ 1.381397] Freeing initrd memory: 3548K [ 1.382365] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 1.384506] Initialise system trusted keyrings [ 1.384883] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.397783] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.399042] NFS: Registering the id_resolver key type [ 1.399095] Key type id_resolver registered [ 1.399106] Key type id_legacy registered [ 1.399330] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.399848] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 1.400673] fuse: init (API version 7.31) [ 1.401758] NET: Registered protocol family 38 [ 1.401779] Key type asymmetric registered [ 1.401791] Asymmetric key parser 'x509' registered [ 1.401856] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.401871] io scheduler mq-deadline registered [ 1.401882] io scheduler kyber registered [ 1.413303] STM32 USART driver initialized [ 1.435753] brd: module loaded [ 1.450481] loop: module loaded [ 1.457161] libphy: Fixed MDIO Bus: probed [ 1.459086] CAN device driver interface [ 1.461523] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 1.461612] usbcore: registered new interface driver pegasus [ 1.461708] usbcore: registered new interface driver asix [ 1.461768] usbcore: registered new interface driver ax88179_178a [ 1.461826] usbcore: registered new interface driver cdc_ether [ 1.461902] usbcore: registered new interface driver smsc75xx [ 1.461978] usbcore: registered new interface driver smsc95xx [ 1.462046] usbcore: registered new interface driver net1080 [ 1.462115] usbcore: registered new interface driver cdc_subset [ 1.462173] usbcore: registered new interface driver zaurus [ 1.462261] usbcore: registered new interface driver cdc_ncm [ 1.463818] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.463873] ehci-platform: EHCI generic platform driver [ 1.464398] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.464440] ohci-platform: OHCI generic platform driver [ 1.465414] usbcore: registered new interface driver cdc_acm [ 1.465428] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.465513] usbcore: registered new interface driver usb-storage [ 1.470664] i2c /dev entries driver [ 1.475453] stm32-cpufreq stm32-cpufreq: Failed to get chip info: -517 [ 1.478820] sdhci: Secure Digital Host Controller Interface driver [ 1.478835] sdhci: Copyright(c) Pierre Ossman [ 1.478845] Synopsys Designware Multimedia Card Interface Driver [ 1.479413] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.480698] ledtrig-cpu: registered to indicate activity on CPUs [ 1.483890] usbcore: registered new interface driver usbhid [ 1.483908] usbhid: USB HID core driver [ 1.484250] arm-smc-mbox mailbox-0: ARM SMC mailbox enabled. [ 1.484383] arm-smc-mbox mailbox-1: ARM SMC mailbox enabled. [ 1.486268] remoteproc remoteproc0: releasing m4 [ 1.489842] Unable to get STM32 DDR PMU clock [ 1.494791] drop_monitor: Initializing network drop monitor service [ 1.495137] NET: Registered protocol family 17 [ 1.495169] can: controller area network core (rev 20170425 abi 9) [ 1.495312] NET: Registered protocol family 29 [ 1.495331] can: raw protocol (rev 20170425) [ 1.495342] can: broadcast manager protocol (rev 20170425 t) [ 1.495360] can: netlink gateway (rev 20190810) max_hops=1 [ 1.496341] Key type dns_resolver registered [ 1.496524] ThumbEE CPU extension supported. [ 1.496552] Registering SWP/SWPB emulation handler [ 1.496994] registered taskstats version 1 [ 1.497009] Loading compiled-in X.509 certificates [ 1.526462] arm-scmi firmware:scmi-0: SCMI Protocol v2.0 'ST:' Firmware version 0x0 [ 1.542578] remoteproc remoteproc0: releasing m4 [ 1.544353] Unable to get STM32 DDR PMU clock [ 1.578028] stm32-cryp 54001000.cryp: will run requests pump with realtime priority [ 1.579724] stm32-cryp 54001000.cryp: Initialized [ 1.592135] remoteproc remoteproc0: releasing m4 [ 1.593941] Unable to get STM32 DDR PMU clock [ 1.631817] stm32-mdma 58000000.dma: STM32 MDMA driver registered [ 1.635161] stm32-dma 48000000.dma: STM32 DMA driver registered [ 1.637488] stm32-dma 48001000.dma: STM32 DMA driver registered [ 1.660168] stm_thermal 50028000.thermal: stm_thermal_probe: Driver initialized successfully [ 1.665435] random: fast init done [ 1.665853] stm32-crc32 58009000.crc: Initialized [ 1.667671] stm32-hash 54002000.hash: will run requests pump with realtime priority [ 1.669592] stm32-hash 54002000.hash: Init HASH done HW ver 23 DMA mode 1 [ 1.670160] random: crng init done [ 1.682282] remoteproc remoteproc0: releasing m4 [ 1.684403] stm32-ddr-pmu: probed (ID=0x00140061 VER=0x00000010), DDR@533MHz [ 1.685051] /soc/interrupt-controller@5000d000: bank0 [ 1.685068] /soc/interrupt-controller@5000d000: bank1 [ 1.685080] /soc/interrupt-controller@5000d000: bank2 [ 1.686823] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added [ 1.687268] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added [ 1.687655] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added [ 1.688037] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added [ 1.688410] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added [ 1.688791] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added [ 1.689148] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added [ 1.689519] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added [ 1.689881] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOI bank added [ 1.689965] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized [ 1.690866] stm32mp157-pinctrl soc:pin-controller-z@54004000: GPIOZ bank added [ 1.690895] stm32mp157-pinctrl soc:pin-controller-z@54004000: Pinctrl STM32 initialized [ 1.693612] 4000e000.serial: ttySTM2 at MMIO 0x4000e000 (irq = 54, base_baud = 4000000) is a stm32-usart [ 1.695369] stm32-usart 40010000.serial: interrupt mode for rx (no dma) [ 1.695393] stm32-usart 40010000.serial: interrupt mode for tx (no dma) [ 1.695430] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 55, base_baud = 4000000) is a stm32-usart [ 2.886860] printk: console [ttySTM0] enabled [ 2.893215] 40011000.serial: ttySTM5 at MMIO 0x40011000 (irq = 56, base_baud = 4000000) is a stm32-usart [ 2.903376] 40018000.serial: ttySTM7 at MMIO 0x40018000 (irq = 57, base_baud = 4000000) is a stm32-usart [ 2.913524] 40019000.serial: ttySTM1 at MMIO 0x40019000 (irq = 58, base_baud = 4000000) is a stm32-usart [ 2.927150] m_can_platform 4400e000.can: m_can device registered (irq=50, version=32) [ 2.938600] stm32_rtc 5c004000.rtc: registered as rtc0 [ 2.942671] stm32_rtc 5c004000.rtc: Date/Time must be initialized [ 2.948466] stm32_rtc 5c004000.rtc: registered rev:1.2 [ 2.973273] stm32f7-i2c 40012000.i2c: doesn't use DMA [ 2.977613] stm32f7-i2c 40012000.i2c: STM32F7 I2C-0 bus adapter [ 3.002613] stm32f7-i2c 40013000.i2c: doesn't use DMA [ 3.006914] stm32f7-i2c 40013000.i2c: STM32F7 I2C-1 bus adapter [ 3.031884] stm32f7-i2c 40015000.i2c: doesn't use DMA [ 3.036233] stm32f7-i2c 40015000.i2c: STM32F7 I2C-2 bus adapter [ 3.063778] stm32f7-i2c 5c002000.i2c: doesn't use DMA [ 3.068895] stpmic1 3-0033: PMIC Chip Version: 0x21 [ 3.073536] genirq: irq_chip stm32-exti-h did not update eff. affinity mask of irq 69 [ 3.081422] BUCK1: supplied by vin [ 3.086833] BUCK2: supplied by vin [ 3.091771] BUCK3: supplied by vin [ 3.096867] BUCK4: supplied by vin [ 3.101801] LDO1: supplied by v3v3 [ 3.107565] LDO2: supplied by vin [ 3.112753] LDO3: supplied by vdd_ddr [ 3.118086] LDO4: supplied by vin [ 3.123219] LDO5: supplied by vin [ 3.128339] LDO6: supplied by v3v3 [ 3.133561] VREF_DDR: supplied by vin [ 3.138653] BOOST: supplied by vin [ 3.141374] VBUS_OTG: supplied by bst_out [ 3.145366] SW_OUT: supplied by bst_out [ 3.151881] input: pmic_onkey as /devices/platform/soc/5c002000.i2c/i2c-3/3-0033/5c002000.i2c:stpmic@33:onkey/i0 [ 3.163062] at24 3-0050: 256 byte 24c02 EEPROM, writable, 16 bytes/write [ 3.168498] stm32f7-i2c 5c002000.i2c: STM32F7 I2C-3 bus adapter [ 3.176857] mmci-pl18x 58005000.sdmmc: Got CD GPIO [ 3.180725] mmci-pl18x 58005000.sdmmc: mmc0: PL180 manf 53 rev2 at 0x58005000 irq 47,0 (pio) [ 3.219634] stm32-ipcc 4c001000.mailbox: ipcc rev:1.0 enabled, 6 chans, proc 0 [ 3.227249] stm32-rproc mlahb:m4@10000000: wdg irq registered [ 3.232109] remoteproc remoteproc0: m4 is available [ 3.340188] iio iio:device0: Failed to exit power down [ 3.344122] stm32-adc: probe of 48003000.adc:adc@0 failed with error -110 [ 3.352520] iio iio:device0: No channels configured [ 3.356193] stm32-adc: probe of 48003000.adc:adc@100 failed with error -61 [ 3.363377] reg11: supplied by vdd [ 3.366521] reg18: supplied by vdd [ 3.370722] stm32-usbphyc 5a006000.usbphyc: registered rev:1.0 [ 3.376406] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_d not found, using dummy regulator [ 3.384530] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_a not found, using dummy regulator [ 3.516225] usb33: supplied by vdd_usb [ 3.518812] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM [ 3.526817] dwc2 49000000.usb-otg: DWC OTG Controller [ 3.530999] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 1 [ 3.538493] dwc2 49000000.usb-otg: irq 86, io mem 0x49000000 [ 3.545329] hub 1-0:1.0: USB hub found [ 3.547902] hub 1-0:1.0: 1 port detected [ 3.553592] ehci-platform 5800d000.usbh-ehci: EHCI Host Controller [ 3.558456] ehci-platform 5800d000.usbh-ehci: new USB bus registered, assigned bus number 2 [ 3.567218] ehci-platform 5800d000.usbh-ehci: irq 59, io mem 0x5800d000 [ 3.596181] ehci-platform 5800d000.usbh-ehci: USB 2.0 started, EHCI 1.00 [ 3.602735] hub 2-0:1.0: USB hub found [ 3.605247] hub 2-0:1.0: 2 ports detected [ 3.610745] ohci-platform 5800c000.usbh-ohci: Generic Platform OHCI controller [ 3.616625] ohci-platform 5800c000.usbh-ohci: new USB bus registered, assigned bus number 3 [ 3.625284] ohci-platform 5800c000.usbh-ohci: irq 48, io mem 0x5800c000 [ 3.701412] hub 3-0:1.0: USB hub found [ 3.703764] hub 3-0:1.0: 2 ports detected [ 3.709566] stm32_rtc 5c004000.rtc: setting system clock to 2000-01-01T00:00:07 UTC (946684807) [ 3.718738] ALSA device list: [ 3.720247] No soundcards found. [ 3.727406] Freeing unused kernel memory: 1024K [ 3.730848] Run /init as init process Starting version 244.3+ root '/dev/disk/by-partuuid/e91c4e10-16e6-4c0e-bd0e-77becf4a3582' doesn't exist or does not contain a /dev.