/dts-v1/;

 #include "osd335x-sm.dtsi"

 / {

 	leds {
 		pinctrl-names = "default", "sleep";
 		pinctrl-0 = <&user_leds_default>;
 		pinctrl-1 = <&user_leds_sleep>;

 		compatible = "gpio-leds";

 		led@2 {
 			label = "beaglebone:green:usr0";
 			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
 			default-state = "off";
 		};

 		led@3 {
 			label = "beaglebone:green:usr1";
 			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "cpu0";
 			default-state = "off";
 		};
 	};

 	vmmcsd_fixed: fixedregulator@0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
 };

 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;

 	status = "okay";
 };

 &usb {
 	status = "okay";
 };

 &usb_ctrl_mod {
 	status = "okay";
 };

 &usb0_phy {
 	status = "okay";
 };

 &usb1_phy {
 	status = "okay";
 };

 &usb0 {
 	status = "okay";
 	dr_mode = "peripheral";
 };

 &usb1 {
 	status = "okay";
 	dr_mode = "host";
 };

 &cppi41dma  {
 	status = "okay";
 };

&ldo3_reg {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-always-on;
};

&mmc1 {
  status = "okay";
  bus-width = <0x4>;
  pinctrl-names = "default";
  pinctrl-0 = <&mmc1_pins>;
  cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
  vmmc-supply = <&vmmcsd_fixed>;
};

&cpu0_opp_table {
	/*
	 * All PG 2.0 silicon may not support 1GHz but some of the early
	 * BeagleBone Blacks have PG 2.0 silicon which is guaranteed
	 * to support 1GHz OPP so enable it for PG 2.0 on this board.
	 */
	oppnitro@1000000000 {
		opp-supported-hw = <0x06 0x0100>;
	};
};

&tscadc {
	status = "okay";
};

&am335x_adc {
	ti,adc-channels = <0 1 2 3 4 5 6 7>;
};

&aes {
	status = "okay";
};

&sham {
	status = "okay";
};

&wkup_m3_ipc {
	ti,scale-data-fw = "am335x-bone-scale-data.bin";
};

&rtc {
	clocks = <&clk_32768_ck>, <&clkdiv32k_ick>;
	clock-names = "ext-clk", "int-clk";
	system-power-controller;
};

&sgx {
	status = "okay";
};

&am33xx_pinmux {

user_leds_default: user_leds_default {
  pinctrl-single,pins = <
    AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.gpio1_16 */
    AM33XX_IOPAD(0x844, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
  >;
};

user_leds_sleep: user_leds_sleep {
  pinctrl-single,pins = <
    AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.gpio1_16 */
    AM33XX_IOPAD(0x844, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
  >;
};

i2c0_pins: pinmux_i2c0_pins {
  pinctrl-single,pins = <
    AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
    AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
  >;
};

uart0_pins: pinmux_uart0_pins {
  pinctrl-single,pins = <
    AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
    AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
  >;
};

mmc1_pins: pinmux_mmc1_pins {
  pinctrl-single,pins = <
    AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
  >;
};

};

&i2c0 {

  baseboard_eeprom: baseboard_eeprom@50 {
    compatible = "at,24c256";
    reg = <0x50>;

    #address-cells = <1>;
    #size-cells = <1>;
    baseboard_data: baseboard_data@0 {
      reg = <0 0x100>;
    };
  };

};

/ {
	model = "SWMS Linux Test Board";
	compatible = "swms,swmw-ltb", "ti,am335x-bone", "ti,am33xx";
};